By Electric FX Inc. · Licensed Electrical Contractor
Landscape lighting installation begins before the first fixture goes into the garden. A dependable result needs a coordinated sequence: review the site, confirm the equipment, prepare the wiring routes, install the system and check the finished lighting after dark.
This homeowner’s guide explains what to organize with your electrical contractor and landscaper in Toronto, the GTA and Simcoe County. It focuses on project delivery and handover. For decisions about the lighting effect itself, start with the landscape layout and the views you want to illuminate.
1. Confirm the design and the construction stage
Bring the current landscape drawing, finished grades, wall details and proposed fixture locations to the initial review. Identify which areas are still under construction and which are already complete. The installation sequence will differ between an open planting bed and a finished terrace.
Walk the proposed route with the people responsible for landscaping, irrigation and electrical work. Decide who provides sleeves, openings and mounting provisions, and who reinstates affected surfaces. Put those responsibilities on the project drawing or written scope.
Confirm fixture models before stonework or decking locks in a mounting detail. A general note saying “step light here” does not establish the opening, fixing arrangement or future replacement access for a particular product.
2. Review the electrical supply separately from the garden circuit
A typical low-voltage landscape system has a mains supply feeding a suitable transformer, followed by the landscape cable network and fixtures. Treat those as distinct parts of the installation. A low-voltage label on the lights does not describe every part of the electrical work.
Have the contractor assess the proposed supply, required protection and equipment location. An existing receptacle should be checked for suitability rather than assumed to be ready because it is close to the garden. ESA’s outdoor guidance discusses GFCI protection and appropriate weather protection for outdoor receptacles.[1]
If new receptacles, circuits or other fixed wiring are needed, identify that work early. Confirm notification and inspection requirements with the Licensed Electrical Contractor or ESA for the actual scope. ESA states that most electrical work requires a notification; do not assume that every landscape project is exempt or that every plug-in kit has the same obligations.[2]
3. Build a cable plan from the final fixture schedule
Give each fixture a reference number and record its model, location and specified electrical load. Draw the route from the transformer to the fixtures, including branches and control groups. Use actual route lengths, allowing for changes in elevation and the way the cable will reach each fitting.
For in-lite systems, the manufacturer’s cable-planning guidance uses the combined VA values of the selected fixtures to check transformer capacity. It also calls for recording cable lengths and reviewing the allocation across outputs.[3]
The installer should check the complete arrangement against the selected system’s instructions, including cable limits and connection methods. A transformer with spare capacity does not by itself establish that an arbitrarily long cable run will work. Do not transfer the cable limits of one manufacturer or product range to another.
Label each proposed branch on the drawing. This makes it easier to discuss which areas should operate together and to locate a problem later without guessing which cable serves the rear garden.
4. Resolve underground conflicts before digging
Arrange the required underground locates before excavation. The locate process must cover the actual work area; an assumption about where a gas service or electrical cable probably runs is not sufficient.
Also identify privately owned infrastructure. Ontario’s locate authority explains that infrastructure beyond the utility demarcation point is the property owner’s responsibility to locate, which may require a private locator.[4] Share known information about feeds to sheds, irrigation, existing garden wiring and other buried systems with the project team.
Ask the electrical contractor to specify the wiring method, protection and burial requirements for each part of the project. Mains wiring and a particular low-voltage lighting system must not be treated as interchangeable. Avoid applying one internet trench-depth figure to every cable or crossing.
Coordinate crossings under paths and other hard surfaces before they are finished. Record the agreed routes and inspect the work at the required stages before covering it.
5. Keep equipment accessible and appropriate for its location
Check the chosen transformer’s mounting, clearance and weather-protection instructions. “Outdoor lighting system” does not mean every component can sit exposed on the ground. The exact model and its installation instructions govern the arrangement.
in-lite’s guidance addresses transformer placement and protective provisions for outdoor mounting.[3] Confirm the current instructions for the supplied product before deciding where it belongs; do not design around a generic photograph of a different unit.
Leave access for operation, inspection and replacement. Consider how future planting, storage or a new fence could obstruct the equipment. A transformer hidden behind a permanently fixed panel may look tidy on handover day but be difficult to service.
6. Install around finished grades and maintenance access
Review the finished ground level before setting fixtures. Discuss soil, mulch, drainage, snow clearing and routine garden maintenance with the landscaper. The fixture location should suit both the intended light effect and the product’s approved installation conditions.
For lights integrated into walls or steps, coordinate mounting and cable access before the finish is complete. Confirm how the light can be replaced without dismantling unrelated work. Where practical, approve a sample detail before repeating it across the property.
Connections should use the components and methods specified for the system and location. Do not assume different brands’ connectors, transformers or fixtures are interchangeable simply because their nominal voltage matches. Have proposed combinations checked before ordering or connecting them.
7. Test operation, then review the lighting after dark
Daytime checks establish whether the equipment operates and the intended groups respond. The evening review answers a different question: does the finished installation produce the agreed result?
Walk the routes in both directions, sit in the normal seating positions and look from the house. Check for direct glare, spill toward neighbouring windows and fixtures whose beam misses the intended feature. Adjust aiming and supported settings before deciding that more lights are needed.
Test schedules and manual operation with the owner. Confirm which controls work locally, which need an app and what access the owner needs to manage the system. Use the selected equipment’s instructions to explain behaviour after a power interruption.
8. Ask for a useful handover
| Handover item | Why it matters |
|---|---|
| Marked fixture and cable plan | Helps future gardening, repairs and additions. |
| Model numbers and instructions | Identifies compatible replacements and operating limits. |
| Control groups and schedules | Lets the owner understand and adjust everyday operation. |
| Photos before routes are covered | Provide a useful project record; they do not replace future locates. |
| Applicable ESA documentation | Records acceptance of the work covered by the notification. |
| Maintenance and service contact | Clarifies who to call and what care the equipment needs. |
Common installation questions
Can the work be done in an established garden?
Often, yes, but the route and access need a site review. Identify planting and finished surfaces that must be protected, then agree on the approach and restoration responsibilities before starting.
Can we reuse an old landscape system?
Possibly. Have the existing supply, transformer, wiring, connections and fixtures assessed. Compatibility and condition determine what can be retained; the presence of old cables alone does not establish that they suit new equipment.
What if the project includes a pool or hot tub?
Flag that at the first review. Electrical work around water needs a separate assessment of the equipment, placement and applicable requirements. A general garden-lighting layout is not a substitute for that review.
Coordinate your installation with Electric FX
Electric FX provides landscape lighting installation in Toronto, the GTA and Simcoe County. Send your plans, property photos, construction schedule and any existing equipment details so we can review the work with your landscaping team. Request a project consultation or visit our landscape lighting service page.
For the factors that affect your budget, read How Much Does Landscape Lighting Cost in Toronto and the GTA?
Planning the lighting effect? Read our landscape lighting design guide.
Sources and further reading
- ESA — Make Your Outdoors Even Greater (outdoor supply and protection guidance).
- ESA — Homeowner Electrical Safety Handbook (notifications and electrical safety).
- in-lite Canada — Cable Planning (system load, routing and transformer placement; verify the exact product manual).
- Ontario locate authority — Demarcation Point: What You Need to Know.
Reviewed October 14, 2026. This is a homeowner’s project-planning guide. It does not prescribe conductor sizes, burial depths, clearances or a universal notification exemption. The actual installation must follow applicable Ontario requirements and the selected equipment’s instructions.