Lighting Design: Key Lighting Metrics

By Electric FX Inc. · Licensed Electrical Contractor

← Electrical Advice & Planning

Lumens, watts, kelvin and CRI describe different qualities of a light. Understanding them helps you compare products and choose lighting that suits your space.

Two LED bulbs can look almost identical on a shelf yet produce very different results at home. One may give off more light, another may use less electricity, and another may make colours appear more faithful. Choosing well means reading these specifications together.

For homeowners and businesses planning lighting upgrades in Toronto, the GTA and Simcoe County, these four metrics are a useful starting point.

The four metrics at a glance

What each number tells you
MetricWhat it describesQuestion it answers
Lumens (lm)Total visible light outputHow much light does it produce?
Watts (W)Electrical power inputHow much power does it use?
Kelvin (K)Warm or cool appearance of white lightWhat colour will the light look?
CRIColour fidelity against a reference lightHow faithfully will it render colours?

These numbers are not interchangeable. A higher Kelvin value does not mean more lumens, and a higher wattage does not necessarily mean more light.[1]

Lumens describe light output

Lumens measure the total amount of visible light a source emits. When comparing replacement bulbs, begin with the lumen rating rather than the old incandescent wattage.[1]

Approximate traditional incandescent replacements
Old incandescent bulbLight output to look for
40 W450 lm
60 W800 lm
75 W1,100 lm
100 W1,600 lm

These are general replacement benchmarks, not a calculation of how many fixtures a room needs.[1] Light distribution and fixture optics affect where the light goes.[2] Compare products intended for the same application: a narrow spotlight and a broad-output bulb can have similar lumens but illuminate a space differently.

Watts describe power use

Watts measure the rate at which a light uses electrical energy. LEDs generally need fewer watts than incandescent bulbs to provide comparable lumen output. The actual input wattage is different from a package’s “60-watt equivalent” description.[1]

Energy used over time is measured in kilowatt-hours (kWh). Calculate it by multiplying watts by operating hours, then dividing by 1,000.

Illustrative example: Ten 9 W LEDs running for four hours use 0.36 kWh. Ten 60 W incandescent bulbs running for the same time use 2.4 kWh. That is 85% less electricity, assuming the selected products provide comparable useful lighting. Actual savings depend on the products and operating hours.

Another useful specification is luminous efficacy: lumens divided by watts, expressed as lm/W.[3] An 800 lm bulb using 8 W provides 100 lm/W; one using 10 W provides 80 lm/W. Compare complete lamps or fixtures on the same basis, and consider colour quality alongside efficiency.

Colour temperature describes warm and cool light

Correlated colour temperature, or CCT, describes the appearance of white light in kelvin. Lower values generally look warmer and more yellow; higher values look cooler and can appear bluish. This is a colour description, not the physical temperature of the bulb.[4]

Practical starting points for colour selection
RangeTypical appearanceWhere to consider it
2700K–3000KWarm whiteLiving rooms, bedrooms, dining areas and kitchens where warmth is preferred
3500K–4100KNeutral to cool whiteKitchens, offices and workspaces where a crisper appearance is preferred
5000K–6500KCool or daylight-like whiteSelected work areas or spaces where a distinctly cool appearance is wanted

These are design starting points, not mandatory room settings. A kitchen can work well at 3000K, and choosing 5000K does not automatically make a workspace better. View samples beside the actual cabinets, paint and countertops before ordering a full set.

Products with the same CCT can still differ in tint or colour rendering.[4] In an open-plan room, compare nearby fixtures together. Matching the number on the box is useful, but a side-by-side check can reveal differences that matter to you.

CRI describes colour fidelity

The colour rendering index compares how a light renders test colours against a reference source at a similar colour temperature. The reference is not always natural sunlight. A general CRI score of 100 represents a match for the test colours, rather than a guarantee that a bulb perfectly reproduces daylight in every respect.[5]

The U.S. Department of Energy describes CRI 90 or higher as excellent colour fidelity.[2] For living spaces and kitchens, CRI 90+ is a useful quality target, especially where food, finishes and furnishings matter. Treat it as a product-selection preference rather than a universal installation requirement.

CRI is not a percentage of “true colour,” and it does not measure brightness. A warm 2700K light can have high CRI, just as a cooler 4000K light can.

For more demanding colour choices, also look for an R9 value, which describes saturated-red rendering, or more detailed TM-30 information. General CRI alone can miss important differences.[2] R9 is not included in the eight-colour average used for general CRI.[5]

Read the specifications together

Imagine an LED labelled 800 lm, 9 W, 3000K and CRI 90. It produces 800 lumens, draws 9 watts, has a warm-white appearance and offers high colour fidelity. None of those numbers tells you whether its shape or beam is suitable for your particular fixture.

When comparing options, write down the full product model and all four metrics. Then ask:

  • Does it provide the output needed for this application?
  • How much power does it use for that output?
  • Does its colour appearance suit the finishes and neighbouring lights?
  • Is its colour rendering appropriate for what people will see and do?

Continue exploring lighting design: The Three Layers of Light; Placement and Height Guidelines; Controls and Efficiency.

Choose lighting with Electric FX

Electric FX helps homeowners and businesses in Toronto, the GTA and Simcoe County plan lighting upgrades, including pot lights, decorative fixtures and LED strip and millwork lighting.

Planning a lighting project? Contact Electric FX to discuss the space, the finishes and the lighting qualities you want before selecting fixtures.

Sources and further reading

  1. U.S. Department of Energy — Purchasing Energy-Efficient Light Bulbs (lumens, power input and replacement benchmarks)
  2. U.S. Department of Energy — LED Basics (optics, colour fidelity and CRI limitations)
  3. Natural Resources Canada — General Service Lamps (luminous efficacy)
  4. U.S. Department of Energy — LED Color Characteristics
  5. National Institute of Standards and Technology — Color Rendering of Light Sources

Research reviewed October 14, 2026. Room suggestions are practical design guidance. Energy and efficacy examples are illustrative calculations, not product specifications or savings guarantees.

Planning an electrical project?

Tell us about your home, renovation or upgrade. Electric FX serves Toronto, the GTA and Simcoe County, with projects also available in Muskoka.