← Electrical Advice & Planning
By Electric FX Inc. · Information checked October 14, 2026
The position of a light can matter just as much as the fixture itself. A few practical measurements help you plan, but the final placement should suit the furniture, the room and the people using it.
For renovations and lighting upgrades in Toronto, the GTA and Simcoe County, it helps to settle fixture locations before ceilings are finished and electrical boxes are installed. Kitchen islands, dining tables and bathroom mirrors give the lighting plan useful reference points.
The measurements below are design starting points. Fixture shape, ceiling height, sightlines and manufacturer instructions can change the final arrangement.
Placement measurements at a glance
| Location | Starting guideline | Measurement reference |
|---|---|---|
| Kitchen island pendants | 30–36 in. (76–91 cm) | Countertop surface to the bottom of the fixture |
| Dining table fixture | 30–36 in. (76–91 cm) | Tabletop surface to the bottom of the fixture |
| Dining fixture width | Approximately half to two-thirds of table width | Fixture diameter or cross-table width; assess linear-fixture length separately |
| Vanity side lights | About 60–66 in. (152–168 cm), adjusted to users | Finished floor to the fixture or light-emitting centre, as appropriate to its design |
| Recessed wall-wash lights | Product-specific setback and spacing | Finished wall to fixture centre; fixture centre to fixture centre |
Manufacturer guidance varies, particularly for fixture proportions and bathroom sconces. Use the following sections to refine the starting measurements.[1] [2] [3] [4] [6]
Kitchen islands — measure from the countertop
A common starting height is 30 to 36 inches between the countertop and the bottom of the pendant. Artika gives this range for standard 8–9 ft ceilings.[1] Measure to the lowest part of the fixture, not to its bulb, canopy or electrical box.
Check the proposed height from both sides of the island. People should be able to prepare food, sit at stools and look across the room comfortably. A deep opaque shade may obstruct a view that an open or smaller fixture leaves clear.
For multiple pendants, Artika suggests 24–30 inches between fixture centres as a starting point, while noting that larger fixtures need more room.[1] Centre-to-centre spacing is different from the open gap between shades: two 16-inch-wide pendants spaced 24 inches centre to centre leave only an 8-inch gap.
Planning example: With a 36-inch-high countertop and a 33-inch gap beneath the pendant, the fixture bottom sits 69 inches above the finished floor. That describes an over-counter position, not a suitable clearance for an open walkway.
Before ordering, check whether the available cord, chain or stem lengths can achieve the chosen height. For sloped ceilings, confirm that the selected mounting arrangement suits the ceiling.
Dining tables — centre the light over the table
Begin with the fixture bottom 30 to 36 inches above the tabletop, consistent with Ethan Allen’s pendant guidance.[2] Centre the fixture over the table’s planned position, which may differ from the centre of the room.
For a round chandelier or pendant, roughly half to two-thirds of the table width is a useful initial sizing range. Manufacturer recommendations differ: Kichler offers half the table width as one diameter guideline, while Ethan Allen suggests larger proportions for some pendant arrangements.[2] [3]
For example, the half-to-two-thirds starting range gives a 24–32-inch fixture diameter over a 48-inch round table. For a rectangular table, use its narrower dimension when assessing fixture width. Assess a linear fixture’s length separately against the table length.
Then review the actual shape. An open-frame fixture and a solid drum shade of the same width can look very different. Sit at the table to check views across it, then stand beside it to check clearance. If the table extends, decide whether the light should be centred on its everyday or extended arrangement.
Bathrooms — place side lights around eye level
Sconces beside a mirror can illuminate the face more evenly than overhead light alone. Visual Comfort recommends approximately 60–65 inches from the floor, around eye level, to help minimize shadows.[4]
The often-used 60–66-inch range is therefore a starting zone rather than a fixed mounting height. Adjust it for the people using the bathroom, the mirror and the fixture’s light-emitting area. A long vertical light may need a different approach from a small shaded sconce.
Confirm the manufacturer’s mounting drawing before setting the electrical box. The box centre, fixture centre and centre of the illuminated portion are not necessarily the same point.
Where side space is limited, a vanity bar above the mirror is another option. Kichler distinguishes this arrangement from side sconces and notes that recessed downlights alone can leave facial shadows.[5] Do not apply the side-light height to an above-mirror fixture.
Aim to reduce facial shadows, rather than promise to eliminate them completely. Check the view in the mirror, allow cabinet doors to open, and coordinate the fixture with the final mirror size before rough-in.
Recessed lights — place them for the surface being lit
Recessed lighting does not always need to follow a grid centred on the floor. Fixtures can serve work surfaces, circulation areas or walls, and those purposes call for different positions.
For wall washing, choose an appropriate fixture or optic and plan both its distance from the wall and its spacing along the wall. Lutron’s Finiré guide explains that beam spread and wall setback affect the result; moving fixtures closer to the wall can also require closer spacing to avoid scalloped patterns.[6]
Simply moving every pot light near a wall does not guarantee an even wash. A standard downward beam may create bright patches, and a layout focused only on the perimeter may leave activity areas poorly served.
Lighting a wall can make it more visually prominent and help a room feel more open, but the effect depends on the wall finish, light distribution and overall layout. Ask for a layout based on the selected fixture’s performance, rather than a universal distance from the wall.
Confirm the layout before rough-in
Bring the following information to the lighting discussion:
- Finished ceiling heights and any slopes or bulkheads.
- Final island, table, vanity and mirror dimensions and positions.
- Fixture model numbers, dimensions and mounting drawings.
- Preferred views through the room and normal seated or standing positions.
- Any cabinet doors, beams or other features that may affect placement.
Mark proposed fixture centres on the plan and confirm the intended finished heights. Where appearance is difficult to judge, a simple cardboard outline can help compare fixture size and sightlines before installation.
Continue exploring lighting design: The Three Layers of Light; Key Lighting Metrics; Controls and Efficiency.
Plan your lighting with Electric FX
Electric FX helps homeowners and businesses in Toronto, the GTA and Simcoe County plan and install pendants, chandeliers, vanity lighting and recessed lights.
Planning a renovation or fixture upgrade? Contact Electric FX to coordinate the lighting positions with your room layout and selected fixtures.
Sources and further reading
- Artika Canada — Pendant Light Height and Spacing
- Ethan Allen Canada — Pendant Lighting (hanging-height and proportion guidance)
- Kichler — About Lighting FAQs (chandelier sizing)
- Visual Comfort — Bathroom Wall Sconces (eye-level placement)
- Kichler — Bathroom Lighting Planning and Selecting Tips
- Lutron — Finiré 3-inch Design Guide, Application Note 622 (wall-wash optics and spacing, pages 15–16)
Research reviewed October 14, 2026. Measurements are design guidance, not electrical-code clearances. Examples and planning suggestions apply the cited principles; final installation must suit the selected products and project conditions.